天堂岛精品🔇_岳的胯香_.手.动.输.入.网.址.联.系.客.服.人.员.lanan_shell
G1000TM Transponder Pilot’s Guide
Record of Revisions Revision Date of Revision Revision Page Range Description A B C D 04/30/04 11/29/04 05/3/05 07/20/05 5-1 – 5-7 5-1 – 5-7 5-1 – 5-5 5-1 – 5-5 Initial release. Added information on .ight ID reporting. Changes per Software 4.02. New cover plus minor edits.
5.1 GTX 33 TRANSPONDER
The GTX 33 transponder is integrated into the G1000 system, offering Mode A, Mode C and Mode S interrogation and reply capabilities. This pilot’s guide provides a description of the transponder operation and information on Mode S capability. The transponder controls are located on the G1000 Primary Flight Display (PFD) on the lower portion of the screen (see .gures below). TRANSPONDER SOFTKEYS The transponder function spans three levels of softkeys; the Top-level, the Mode Selection and the Code Selection softkeys. When the Top-level XPDR softkey is pressed, the following softkeys appear in the softkey bar (Figure 5.1.2): STBY, ON, ALT, VFR, CODE, IDENT, BACK. When the CODE softkey is pressed, the number softkeys appear in the softkey bar (Figure 5.1.3): 0, 1, 2, 3, 4, 5, 6, 7, IDENT, BKSP, BACK. The digits 8 and 9 are not used for code entry. Pressing the BKSP softkey backs up code selection to the previous digit. Pressing the BACK softkey during code selection reverts to the MODE Selection softkeys (Figure 5.1.2). Pressing the BACK softkey during Mode Selection reverts to the Top-level softkeys (Figure 5.1.1).
NOTE: After 45 seconds of transponder softkey inactivity, the system reverts back to theTop-level softkeys (Figure 5.1.1).
TRANSPONDER STATUS BAR The Transponder Status bar is located to the left of the System Time box and contains, a four-digit code .eld, a mode .eld and a reply status indicator. In Standby mode, both the code .eld and the mode .eld appear in white. In all other modes, these .elds appear in green.
Transponder Status Bar
Pressing BACK Figure 5.1.2 Mode Selection Softkeys displays the Code
displays the Mode Selection softkeys
Figure 5.1.3 Code Selection Softkeys
190-00382-00 Rev. D Garmin G1000 Transponder Pilot’s Guide
MODE S FEATURES The GTX 33 transponder is equipped with selective addressing or Mode Select (Mode S), capability. Mode S functions include the following features: . Level-2 reply data link capability (used to exchange information between aircraft and various ATC facilities)
. Surveillance identi.er capability
. Flight ID reporting
. Altitude reporting
. Airborne status determination
. Transponder capability reporting
. Mode S Enhanced Surveillance (EHS) requirements
. Acquisition squitter
Flight ID Reporting – The G1000 transponder reports aircraft identi.cation as either the aircraft registration or a FLT ID (Flight Identi.cation). The system is con.gured for either option by an authorized Garmin service center. If con.gured for Flight ID entry, the pilot must enter the appropriate .ight ID on the PFD. After the correct Flight ID is entered, the aircraft identi.cation reported in response to ATC radar interrogations is properly correlated with the associated call sign for voice communication. The .ight ID is not to exceed seven (7) characters. No space is needed when entering Flight ID. When a Flight ID contains a space, the system automatically removes it upon completion of Flight ID entry. (See ICAO documents 8168, 4444 and 8585 for further details). If the Flight ID is set to ‘SAME AS TAIL’ no entry is required. In this con.guration, the transponder then reports the aircraft registration number to ATC. www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：G1000TM Transponder Pilot’s Guide 应答机飞行员指南
