国产自拍👅_免费的网络舆情网站_.手.动.输.入.网.址.联.系.客.服.人.员.lanan_shell
LUBRICATION - DESCRIPTION AND OPERATION _______________________________________ 1. General _______ The lubrication instructions define:
-Specification of the lubricant to be used -Points to be lubricated - Special precautions to be observed.
A. Equipment and Materials Depending on the type of lubrication, use:
-a grease gun -an oil can - a brush
- a clean lint-free cloth
B. Lubricant Specifications The lubricant references are given in the list of materials required for aircraft servicing and maintenance (Ref. ATA 20-31).
C. General Requirements
(1) Use only clean lubricants and tools for lubrication operations.
(2) Before starting any lubricating operation, carefully clean the grease nipples lubricating holes. Lubrication must be accomplished immediately. Check that grease nipples and fitted with ball and spring.
(3) Ensure that the old grease exudes through the pressure relief valves and on each side of the spherical bearings (unless the quantity of grease to be used is indicated).
(4) After lubrication, remove all surplus grease. Wipe the grease nipple with a clean, lint-free cloth. Check that the ball and its spring are in position.
(5) Before lubrication, the wheel bearings should be cleaned. The bearings should be lubricated and installed immediately.
D. Lubrication Symbols (Ref. Fig. 001) The symbols used represent the recommended lubrication method. Below each symbol, an index indicates:
-First term : the lubrication point location -Second term : the lubricant to be used.
Lubrication Symbols Figure 001 1EFF : ALL 1 12-22-00 Page 2 1 1 Feb 01/98 1 1 1CES 1
FLIGHT CONTROLS - SERVICING ___________________________ TASK 12-22-27-640-003 Lubrication of Trimmable Horizontal Stabilizer Actuator Ball Screw Nut WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU _______ START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING _______ GEAR.
1. Reason for the Job __________________ Refer to the MPD TASK: 274451-01 2. Job Set-up Information ______________________ A. Fixtures, Tools, Test and Support Equipment -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION ------------------------------------------------------------------------------- No specific circuit breaker(s) safety clip(s) No specific container 1l No specific gun - grease No specific pin - non-metallic No specific safety barriers No specific warning notice No specific access platform 4.5 m (14 ft. 9 in.)
B. Consumable Materials -------------------------------------------------------------------------------REFERENCE DESIGNATION ------------------------------------------------------------------------------- R Material No. 04-004 USA MIL-PRF-23827 TYPE I SYNTH.ESTER BASED GREASE HIGH PRESSURE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information -------------------------------------------------------------------------------REFERENCE DESIGNATION ------------------------------------------------------------------------------- R 24-41-00-861-002 R R 24-41-00-862-002 R R 29-23-00-863-001 R R R 29-23-00-864-001 R R 29-24-00-863-001 R R 29-24-00-864-001 R 31-60-00-860-001 R 31-60-00-860-002 12-22-27-991-003 3. Job Set-up__________
Energize the Aircraft Electrical Circuits from the External Power De-energize the Aircraft Electrical Circuits Supplied from the External Power Pressurize the Green Hydraulic System from the Yellow Hydraulic System through the PTU with the Electric Pump Depressurize the Green and Yellow Hydraulic Systems after Operation of the PTU Pressurize the Yellow Hydraulic System with the Electric Pump Depressurize the Yellow Hydraulic System EIS Start Procedure EIS Stop ProcedureFig. 301 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM SERVICING 2
