在线看免费❗_公主肚子疼小说_.手.动.输.入.网.址.联.系.客.服.人.员.lanan_shell
TO: HOLDERS OF STANDARD PRACTICES MANUAL, ATA NO. 20-00-02/70-00-01, REVISION 6, DATED APRIL 23, 1999. APPLICATION: GENERAL REVISION NO. 7, DATED APRIL 1, 2005 This is a COMPLETE revision. Pages revised are listed below, together with the Highlights of the revision. Do to the extent of the changes, this publication has been reprinted in its entirety. Please discard entire manual of previous issues and replace with this complete manual. HIGHLIGHTS Changed references from AlliedSignal to Honeywell throughout. Changed headers and footers throughout. Updated all Table of Contents to reflect revised and added procedures. Updated List of Effective Pages to reflect revised and added procedures.
Reformatted cross-references for consistency. Adjusted all Table and Figure numbers as necessary. Subject/Page Description of Contents Title Page Revised to latest revision date. Record of Revisions Added Revision 7 List of Effective Pages Revised to reflect changed pages. INTRODUCTION Page 1 Added "Workscope Planning Guides" to second paragraph. SECTION II - CLEANING Page 205 Added Method No. 202H. Page 206 Revised Method No. 203B per TR 20-31/70-31. Page 219 Revised note for Method No. 203R per TR 20-36/70-36. Pages 221 through 226 Added Method No. 203T and 203U per TR 20-30/70-30. Added Method No. 203V. SECTION III - INSPECTION Page 301 Revised text under Step A. Page 302 Revised text on Note following Step D.(4). Page 334 Added Table 306.
Page 1 of 2 Highlights Apr 1/05 20-00-02/70-00-01
Subject/Page Page 335 Page 337 Pages 341 through 349 Pages 354 through 359 Page 360 Pages 361 through 364
SECTION IV - REPAIR Pages 409 through 410 Pages 417 through 421 Page 427 Page 430 Page 431 Page 443 Pages 448 through 450 Pages 451 through 456 Pages 468 through 481/482 SECTION VII - APPENDIX Page 725 Page 727 Page 729 Pages 731 and 732 Page 733 STANDARD PRACTICES MANUAL 20-00-02/70-00-01 HIGHLIGHTS (CONT) Description of Contents Added Paragrah G.(1)(d). Added inspection for pins in wiring harness. Added optional runout and tooth bearing pattern check. Corrected Step numbers. Added Step N. Added Step O.
Added Methods 1 through 9 of metal spray repair. Added Method No. 403I, 403J, 403K, and 403L. Added Note for Method 406A. Added Method No. 406C per TR 20-39/70-39 Added Note and Caution for Method No. 407A. Added Figure 404. Modified Note for repairing welded parts. Added
Method No. 411A, 411B, and 411C.
Added Steps (1) and (2) to Method No. 412C. Adjusted for number roll. Added Steps 15 through 17.
Revised the balancing machine model in Table 705 per TR 20-43/70-43. Added ethyl alcohol to Table 706 per TR 20-24/70-24. Added lint free cloth to Table 706 per TR 20-25/70-25. Added plastic abrasive media to Table 706 per TR 20-26/70-26. Replaced solvent (Shell 360), added sodium hydroxide and vinyl masking tape to Table 706 per TR 20-32/70-32 and TR 20-27/70-27. Page 2 of 2 Highlights Apr 1/05 20-00-02/70-00-01
STANDARD PRACTICES MANUAL LIMITED DISTRIBUTION TO AUTHORIZED PERSONS ONLY This document and all information and expression contained herein are the property of Honeywell Inc., are loaned in confidence, and may not, in whole or in part, be used, duplicated, or disclosed for any purpose without prior written permission of Honeywell Inc. All rights reserved. Copyright Honeywell Inc. 1977, 1999, 2005. This Publication was prepared by Honeywell Engines, Systems & Services www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：标准施工手册 STANDARD PRACTICES MANUAL 20-00-02/70-00-01
