糖心logo官网✅_色婷婷久婷婷_.手.动.输.入.网.址.联.系.客.服.人.员.lanan_shell
Hand Crimping Tool-SOURIAU P/N CCT 1612 R Figure 028
Hand Crimping Tool - DANIELS M309 R Figure 029
_________________________________________________________ HYDRAULIC HAND CRIMPING TOOLS - DESCRIPTION AND OPERATION _______________________ 1. List of Described Tools -Hand Hydraulic Crimping Tool P/N 69061, 69062, 69062-2 and 59975-1 __________________________________________________________________
2. Hand Hydraulic Crimping Tool P/N 69061, 69062, 69062-2 and 59975-1 (Ref. Fig. 001) A. Installation of Crimping Dies or Nests The head of the tool holds two dies for crimping of wires gauge 8 to 2. Correct positioning of dies is performed as follows : (1) Press latch to open crimping head.
(2) Pull back nest lock and rotate thumb knob until the desired nest is obtained.
(3) With nest properly located, nest lock will spring back into position. If not the case, nest lock will not spring back into position and crimping head will not close.
(4) Close crimping head.
B. Example of Crimping (1) Open pressure relief valve for a few seconds to ensure that indenter is located in neutral position. Close pressure relief valve.
(2) Locate splice between indenter and nest, with brazed seam facing indenter.
(3) Using short pumping strokes, pump handles sufficiently to hold splice in position without deferming barrel.
(4) Insert stripped end of wire into splice barrel.
(5) Continue pumping strokes until handles require less effort to pump showing that pressure relief valve operates and that crimping cycle is complete.
(6) Open pressure relief valve lever until indenter returns to neutral position.
(7) Open crimping head and remove crimped assembly.
Hand Hydraulic Crimping Tool P/N 69061, 69062, 69062-2 and 59975-1 Figure 001
____________________________________________________ PNEUMATIC CRIMPING TOOLS - DESCRIPTION AND OPERATION R R _______________________1. List of Described Tools - PICO Crimping Tools Model 500D1 - CANNON Crimping Tools Model CBT600 and CBT600B - AMP Pneumatic Hand Tool P/N 69365 - DANIELS Pneumatic Crimping Tool WA27-309-EP _______________________________2. PICO Crimping Tools Model 500D1 A. Designation (Ref. Fig. 001) (1) Model 500D1 crimping tool is used for crimping of Flight Connector contacts, gauge 8 to 4/0. R R (2) This is a full-cycling pneumatic tool which cannot be opened until full crimping cycle has been completed. (3) This tool operates on a supply of clean dry air or inert gas within a pressure range of 6 to 9 bars, depending on the size of contact to be crimped. B. Example of Crimping (1) With tool in full operating condition, insert contact and wire. (2) Press trigger. (3) Note that indentors cannot be opened until full crimping cycle is completed.
PICO Crimping Tool Model 500D1 Figure 001
______________________________________________3. CANNON Crimping Tools Model CBT600 and CBT600B A. Designation (Ref. Fig. 002) The model CBT600 is an air-operated crimping tool which can be operated with a hand valve or foot valve. It can also operate as a portable crimping tool. A basic model CBT600 crimps any contact size 12 through size 4 at the air line pressure of 80 to 100 PSI. The model CBT600B crimps contacts size 0 at the air line pressure of 120 PSI. The tool must be equipped with an air line filter and lubricator for optimum performance. B. Locator Part Numbers ------------------------------------------------------ | CONTACT | POWER | CRIMP | | | | SIZE | CRIMP | HEAD | LOCATOR | GAUGE | | | TOOL | | | | |---------|----------|----------|-----------|---------| | 12 | CBT600 | CCH-12-7 | CCHP-12-2 | --| |---------| |----------|-----------|---------| | 8 | OR | CCH-8-1 | CCHP-8-1 | CCH-8-1 | |---------| |----------|-----------|---------| | 4 | CBT600B | CCH-4-1 | CCHP-4-1 | CCH-4-1 | |---------|--------- |----------|-----------|---------| | 0 | CBT600B | CCH-0-1 | CCHP-0-9 | CCH-0 | ------------------------------------------------------- C. Example of Crimping (1) Insert the locator into the power unit. www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320 ESPM Electrical Standard Practices Manual 2
