国产自拍👅_瑟图片配图_.手.动.输.入.网.址.联.系.客.服.人.员.lanan_shell
B. Do the test given in Para. 3. 5. Close-up________ A. Depressurize the Blue hydraulic system (Ref. AMM TASK 29-10-00-864-003).
Loss of the Blue Hydraulic Pressure Transducer Signal for the ELAC 1 1. Possible Causes _______________ - ELAC-1 (2CE1)
- wiring of the ANI 4-3 signal from the ELAC 1 (2CE1) COM and MON parts to the first terminal block
2. Job Set-up Information ______________________ A. Referenced Information -------------------------------------------------------------------------------REFERENCE DESIGNATION ------------------------------------------------------------------------------- AMM 27-93-34-000-001 Removal of the ELAC (2CE1,2CE2) AMM 27-93-34-400-001 Installation of the ELAC (2CE1,2CE2) AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning)
R AMM 29-10-00-863-003 Pressurize the Blue Hydraulic System with a Ground R Power Supply AMM 29-10-00-864-003 Depressurize the Blue Hydraulic System ASM 27-92/28 3. Fault Confirmation __________________ A. Job Set-Up (1) Pressurize the Blue hydraulic system with the electric pump (Ref. AMM TASK 29-10-00-863-003). B. Test (1) Do the BITE test of the EFCS (Ground Scanning) (Ref. AMM TASK 27-96-00-740-001). 4. Fault Isolation _______________ A. If the BITE test gives the maintenance message: ELAC1 OR WIRING FROM B HYD PRESS XMTR 2065GN
- replace the ELAC-1 (2CE1), (Ref. AMM TASK 27-93-34-000-001) and (Ref. AMM TASK 27-93-34-400-001). (1) If the fault continues: - do a check and repair the wiring of the ANI 4-3 signal from the ELAC 1 (2CE1) COM and MON parts to the first terminal block, (Ref. ASM 27-92/28). B. Do the test given in Para. 3. 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-93-00∞∞∞∞∞∞∞∞∞∞Page 239 May 01/00 CES
5. Close-up ________ A. Depressurize the Blue hydraulic system (Ref. AMM TASK 29-10-00-864-003).
Loss of the Blue Hydraulic Pressure Transducer Signal for the ELAC 2 1. Possible Causes _______________ - ELAC-2 (2CE2)
- wiring of the ANI 4-3 signal from the ELAC 2 (2CE2) COM and MON parts to the first terminal block
2. Job Set-up Information ______________________ A. Referenced Information -------------------------------------------------------------------------------REFERENCE DESIGNATION ------------------------------------------------------------------------------- AMM 27-93-34-000-001 Removal of the ELAC (2CE1,2CE2) AMM 27-93-34-400-001 Installation of the ELAC (2CE1,2CE2) AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning)
R AMM 29-10-00-863-003 Pressurize the Blue Hydraulic System with a Ground R Power Supply AMM 29-10-00-864-003 Depressurize the Blue Hydraulic System ASM 27-92/28 3. Fault Confirmation __________________ A. Job Set-Up (1) Pressurize the Blue hydraulic system with the electric pump (Ref. AMM TASK 29-10-00-863-003). B. Test (1) Do the BITE test of the EFCS (Ground Scanning) (Ref. AMM TASK 27-96-00-740-001). 4. Fault Isolation _______________ A. If the BITE test gives the maintenance message: ELAC2 OR WIRING FROM B HYD PRESS XMTR 2065GN
- replace the ELAC-2 (2CE2), (Ref. AMM TASK 27-93-34-000-001) and (Ref. AMM TASK 27-93-34-400-001). (1) If the fault continues: - do a check and repair the wiring of the ANI 4-3 signal from the ELAC 2 (2CE2) COM and MON parts to the first terminal block, (Ref. ASM 27-92/28). B. Do the test given in Para. 3. 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-93-00∞∞∞∞∞∞∞∞∞∞Page 241 May 01/00 CES
5. Close-up ________ A. Depressurize the Blue hydraulic system (Ref. AMM TASK 29-10-00-864-003).
Loss of the Green Hydraulic Pressure Switch Signal for the ELAC 1 1. Possible Causes _______________ - ELAC-1 (2CE1)
- wiring of the LOW GREEN PRESS signal from the ELAC 1 (2CE1) to the first terminal block
2. Job Set-up Information ______________________ A. Referenced Information ------------------------------------------------------------------------------- REFERENCE DESIGNATION www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320 Trouble Shooting Manual 排故手册 飞行操纵 3
