糖心logo官网✅_麻豆星空传媒果冻传媒大象_.手.动.输.入.网.址.联.系.客.服.人.员.lanan_shell
S 014-007 (3) Remove the parts that follow to disconnect the lower end of the spring cartridge for the nose wheel steering from the upper torsion link.
(4) Remove the lockbolt (17) from the pin for the upper torsion link.
(5) Remove the parts that follow to disconnect the upper torsion link from the steering collar (View B-B).
32-21-09 ALL ú ú 01 Page 403 ú May 28/99 A
757 MAINTENANCE MANUAL
S 024-008 (6) Remove the upper torsion link (11). TASK 32-21-09-004-015 3. Install the Upper Torsion Link for the Nose Landing Gear ________________________________________________________ A. Consumable Materials (1) D00633 Grease - BMS 3-33 (Recommended)
(2) D00013 Grease - MIL-G-23827 (Alternative)
~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 1 | Bolt | 32-51-06 | 01 | 170 | | | 2 | Bushing | | | 185 | | | 3 | Washer | | | 175 | | | 4 | Nut | | | 180 | | | 5 | Lower Torsion Link | 32-21-01 | 01 | 70 | | | 6 | Pin | | | 68 | | | 7 | Lockbolt | | | 57 | | | 8 | Washer | | | 60 | | | 9 | Nut | | | 65 | | | 10 | Pin | | | 20 | | | 11 | Upper Torsion Link | | | 50 | | | 12 | Apex Pin | | | 25 | | | 13 | Washer | | | 30 | | | 14 | Washer | | | 29 | | | 15 | Nut | | | 32 | | | 16 | Tang Washer | | | 27 | | | 17 | Lockbolt | | | 5 | | | 18 | Washer | | | 10 | | | 19 | Nut | | | 15 | 2.......….......…...................................…...........….....…........1 C. References (1) AMM 32-00-20/201, Landing Gear Downlocks
(2) AMM 32-09-08/201, Nose Gear Not Compressed Sensors
(1) Location Zones 211/212 Control Cabin 711 Nose Landing Gear (NLG) 713/714 Forward NLG Doors 715/716 Aft NLG Doors
32-21-09 ALL ú ú 01 Page 404 ú May 28/01 A
757 MAINTENANCE MANUAL E. Install the upper torsion link. S 414-017 (1) Apply grease to, and install, the parts that follow to connect the upper torsion link (11) to the shock strut (View B-B).
(b) Lockbolt (17)
(d) Nut (19) 1) Tighten the nut to 90-125 pound-inches.
NOTE: If necessary, you can loosen the nut to the ____ nearest lock position to install the cotter pin. (e) Cotter Pin S 414-020 (2) Install these parts to connect the lower end of the spring cartridge for the nose wheel steering to the upper torsion link (11):
S 424-022 (3) Apply grease to, and install, the parts that follow to connect the upper torsion link (11) to the lower torsion link (5) (View B-B).
(a) Apex Pin (12)
(b) Washers (13, 14, and 16)
(c) Nut (15) 1) Tighten the nut to 200-250 pound-inches.
F. Put the Airplane Back to Its Usual Condition
S 864-060 (1) Remove the DO-NOT-OPERATE tags from the control lever for the landing gear. Put the lever in the DN position.
(2) Lubricate the torsion link at the grease fittings.
32-21-09 ALL ú ú 01 Page 405 ú Sep 28/01 A 757 MAINTENANCE MANUAL S 824-028 (3) Do this task "Measure/Adjust the Clearance for the Nose Landing Gear Not Compressed Sensor" (AMM 32-09-08/201), if you did one of the tasks that follow: www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：757 AMM 飞机维护手册 起落架 CHAPTER 32 - LANDING GEAR 2
